上海法登气动单作用执行器 单动气动头报价
价格:电议
地区:上海市
电 话:13621836061
手 机:13621836061
传 真:02154722967

上海法登气动单作用执行器     单动气动头报价

Maintenance & Operating InstructionsVATTEN? ACTUATOR OPERATIONNOTE: For optimal operation, VATTEN actuators should be run with a supply of clean, lubricated air.SPRING RETURN ACTUATORSAir to PORT 2 (the right hand port) causes the actuator to turn CCW. Loss of air to PORT 2 causes air toexhaust and the actuator turns CW. This is the FAIL CLOSE operation.DOUBLE ACTING ACTUATORSAir to PORT 2 (the right hand port) causes the actuator to turn CCW. Air to PORT 1 (the left hand port)causes the actuator to turn CW.DISASSEMBLING STANDARD ACTUATORSIMPORTANT: Before beginning disassembly, ensure that the air supply to the actuator has been disconnected, allaccessories have been removed and that the actuator has been dismounted from the valve.1. Loosen the end cap fasteners (22) with a wrench (size varies depending on actuator model). On the spring returnactuator, alternate 3 to 5 turns on each fastener until the springs are completely decompressed. Use caution inremoving the cap since the springs are under load until the fasteners are fully extended.2. Remove the pinion snap ring (10) with a lock ring tool. The indicator (7) may now be removed.3. Turn the pinion shaft (2) CCW until the pistons are at the full end of travel. Disengage the pistons (11) from thepinion. (NOTE: Low pressure air--3 to 5 P.S.I. MAXIMUM--might be required to force the pistons completelyfrom the body.) Note the position of the pistons before removing them from the actuator body. The part numbersof the pistons are located on the side and should be right-side up on an actuator with a standard orientation.4. Remove the pinion through the bottom of the actuator. The actuator is now completely disassembled. Allreplacement parts may now be put in. VATTEN recommends that all wear parts (3, 4, 5, 6, 12, 13, 14) bereplaced before reassembly.REASSEMBLING STANDARD ACTUATORSIMPORTANT: Be sure that the actuator surfaces are free of grit and scratches before reassembling.1. Apply a light film of grease to all o-rings and the pinion before replacing.2. Put the pinion (2) back through the actuator with the flats of the pinion shaft running parallel with the body.3. When reassembling the actuator, make sure that the piston racks are square to the actuator body and returned totheir original orientation. (NOTE: The normal operation of all VATTEN actuators is FAIL CLOSED. If you wantto change the orientation to FAIL OPEN, rotate the racks 180o to create a reverse operation.4. When replacing springs in a spring return actuator, ensure that the springs are replaced in their identical positionin the end cap from which they were removed. (NOTE: In some circumstances, you might want to change thestandard 80 pound spring set to fit your application and available air pressure. Changing the spring sets onVATTEN actuators requires no special tools. Please refer to the spring combination torque chart in our catalogfor the inner and outer spring combinations that will allow you to operate with the spring set that you desire.5. Seal the end caps with a petroleum lubricant and bolt to actuator body.6. Check the seal of the actuator by covering seal areas (pinion, end caps) with soapy water and using low pressureair to the actuator to ensure that no bubbles are produced.


品牌/商标

VATTEN

企业类型

制造商

新旧程度

全新

产品型号

VA75DA

原产地

上海

材质:

铝合金

压力:

常压

温度:

常温

开关次数:

100万次