英国TTi PL-P系列可编程稳压电源 PL155P PL303P PL303QMD-P

PL-P系列是TTI新的线性稳压电源系列可编程产品。有手动控制的功能，但增加了全面的远程控制功能。

超紧凑型架模块尺寸非常适合安装在机架上的测试系统，而保留台式应用的手动控制程序。

为了满足今天的工程师们的不同需求，提供一系列的接口。RS-232接口，USB和LAN（以太网）与LXI支持提供标准。

每个数字总线接口提供的电压，电流控制，输出开/关，加回读电压，电流和地位。

     产品特点：

• 高性能的线性稳压电源
• 全数字化远程控制和读出
• RS-232接口，USB和LAN（以太网）
• LAN接口符合LXI标准
• 接口的光电隔离输出
• IVI驱动器提供
• V模拟远程控制和我（非隔离）
• 简单的主从式并行布线模拟输出
• 季度架3U超紧凑的尺寸
• 高功率密度达90瓦特输出
• 宽范围的单和双输出模型；
• 按新的PL系列手动控制功能

     产品型号/规格：

• PL155-P - 0 to 15V at 0 to 5A
• PL303-P - 0 to 30V at 0 to 3A
• PL601-P -  0 to 60V at 0 to 1.5A
• PL303QMD-P - 2 x (0 to 30V at 0 to 3A)
  Digital Bus Interfaces - RS-232, USB, LAN (LXI)

Full remote control and read-back using RS-232, USB or LAN (LXI-C). All interfaces are at ground potential and opto-isolated from the outputs.

Note: Remote/Local Sense, and Operational Mode (PL303QMD-P) are manually selectable only.

RS-232

Standard 9-pin D connector. Baud rate 19,200 max.

USB

Standard USB hardware connection. Operates as a virtual COM port.

Ethernet (LAN)

Standard 10/100 base-T hardware connection. ICMP and TCP/IP Protocol for connection to Local Area Network or direct connection to a single PC.

LXI Compliance

LAN interface is compliant with LXI-C. (LXI is the abbreviation for Lan eXtensions for Instrumentation).

GPIB (only with option G)

Conforms with IEEE-488.1 and IEEE-488.2.

Digital Programming Performance

Voltage Setting

Setting Resolution: 1mV
Setting Accuracy: +/- (0.05% +10mV)

Current Setting

Setting Resolution: 0.1mA (0.01mA on 500mA range)
Setting Accuracy: +/- (0.3% +0.005A) to 3A, +/- (0.5% +0.005A) to 6A, +/- (0.3% +0.5mA) on 500mA range.

Programming Speed

Command Delay: Typically <80ms (this must be added to any of the figures below)
Voltage Up Time: Typically <45ms* to 1%
Voltage Down Time: Typically <20ms* to 1% (full load); typically <150ms* to 1% (no load)

* The up and down times vary with model, current range and voltage step size. More information is contained in the operating manual which can be downloaded from our web site.

Analog Remote Control (single output models only)

Non-isolated analog voltage control of voltage and current. Analog control outputs are also provided to enable easy parallel connection of multiple units in a master-slave configuration.
Note that the PL303QMD-P does not have analog remote control.

Scaling

Reference Point: All control voltage are referenced to the positive output terminal
Set Voltage Input: 0V to 10V sets 0 to 100% of rated output (e.g. 0 to 30V for PL303-P).
  Alternative scaling of 0V to 5V (selectable using internal link).
Set Current Input: 0V to 10V sets 0 to 100% of rated output (e.g. 0 to 3A for PL303-P).
  Alternative scaling of 0V to 5V (selectable using internal link).
Voltage Output: 0 to 100% of rated output voltage generates 0V to 5V.
Current Output: 0 to 100% of rated output current generates 0V to 5V.

Accuracy

Set Voltage Input: +/- (0.3% +10mV); Input Impedance = 100kOhm
Set Current Input: +/- (0.5% +0.005A); +/- (0.5% +0.5mA) on 500mA range

Input Impedance = 64kOhm

Voltage Output: +/- (0.3% +10mV); Output Impedance = 125Ohm
Current Output: +/- (0.5% +0.005A); +/- (0.5% +0.5mA) on 500mA range; Output Impedance = 125Ohm

Remote Analog On/Off Control (single output models only)

Non-isolated terminal which sets the output to Off when pulled low by gate signal or relay closure. Signal is reference to the positive output terminal.
Note that the PL303QMD-P does not have this facility.

Rear Terminals

Power and sense connections are duplicated on the rear panel using a screw-less connector block.
Digital Bus Interfaces - RS-232, USB, LAN (LXI)

NOTE: The above specifications are additional to the Manual Control specifications which can be seen Here.

GENERAL SPECIFICATIONS

Input

AC Input: 230V AC or 115V AC +/- 10%, 50/60Hz. Installation Category II
Input Power: Single output models - 280VA max.; Dual output models - 560VA max.

Temperature & Environmental

Operating Range: +5oC to +40oC, 20% to 80% RH
Storage Range: -40oC to + 70oC
Environmental: Indoor use at altitudes up to 2000m, Pollution Degree 2.
Cooling: Intelligent variable-speed low noise fan assists convection.

Safety & EMC

Safety: Complies with EN61010-1
EMC: Complies with EN61326

Physical

Size: Single output models - 107mm x 131mm (1/4 rack 3U) x 343mm,
Dual output models - 214mm x 131mm (1/2 rack 3U) x 288mm
Triple output models - 321mm x 131mm (3/4 rack 3U) x 288mm
(sizes exclude feet, knobs and terminals).
Weight: Single output models - 4.55kg (10lb);
Dual output models - 9.05kg (19.9lb)
Triple outpuut models - 13.0kg (28.6ib)

DRIVER SOFTWARE SUPPLIED

IVI Driver

An IVI driver for Windows is supplied. This provides support for common applications such as LabView*, LabWindows*, HPVEE* etc.

USB Driver

An installation file is supplied which calls a standard Windows* USB driver.

* LabView and LabWindows are trademarks of National Instruments. HPVEE (now Agilent VEE) is a trademark of Agilent Technologies. * USB interface is supported for Windows 98-SE, 2000, XP, and Vista. Windows is a trademark of Microsoft.

OPTIONS

Rack Mount (RM450)

19 inch 4U rack mount suitable for up to four single power supplies, two dual power supplies, or any mixture. Blanking plates are provided for unused positions. The 4U height provides limited ventilation space above and below the power supplies.

GPIB Interface (Option G)

GPIB (IEEE-488) interface fitted in addition to other interfaces.