BAD83防爆无极灯 ，BEW防爆无极灯 ccd92防爆无极灯，ccd93系列防爆无极灯 ，BAD81防爆无极灯 BAD83系列防爆无极灯是公司主打产品之一 价格和质量也是防爆行业的标准 是公司销量的产品  以此本公司向广大客户推荐此类产品 望广大客户前来咨询订购

BAD83防爆无极灯 ，BEW防爆无极灯 ccd92防爆无极灯，ccd93系列防爆无极灯 ，BAD81防爆无极灯 BAD83系列防爆无极灯是公司主打产品之一 价格和质量也是防爆行业的标准 是公司销量的产品  以此本公司向广大客户推荐此类产品 望广大客户前来咨询订购

一，主要适用于爆炸性气体环境中1区或2区危险区域，为ⅡC或ⅡB类T2组及以下场所，在交流50Hz、额定电压至220V的电路中，作为工作场所照明之用。

二，BAD83防爆无极灯主要结构防爆灯由铝合金外壳、玻璃罩和保护网等几部分组成。隔爆型机构。防爆灯的外壳采用ZL102铸铝合金压铸制成，玻璃罩采用钢化玻璃制成。防爆灯设有内外接地螺钉和接线腔，适合电缆或钢管布线。防爆灯可有多种安装方式，采用快速拆装结构，便于快速更换灯泡。一体式防爆灯，镇流器可放入灯体内，外型美观，分体式防爆灯，镇流器需另配。

三，BAD83防爆无极灯防爆灯在下列条件下能够可靠工作 1、安装地点的海拔不限制。 2、周围环境温度为-20℃～+40℃时，且24h内的平均值不超过35℃ 3、安装地点的空气相对湿度在温度为+40℃时，不超过50%，在较低的温度下允许有较高的相对湿度，湿的月平均温度不超过+25℃，该月平均相对湿度不超过90%。 4、在无剧烈振动，冲击及摇动的地方。 5、在含有爆炸性气体环境场所。 6、污染等级为3级。

四、BAD83防爆无极灯使用及维修 1、防爆灯在安装前，应检查铭牌上所列技术数据及使用说明书中的基本参数是否与实际使用情况相符，并检查元件是否损坏、各部位是否完好、正常。安装时先将进线电缆通过引入装置接到接线腔的接线端子上，并压紧密封圈，使电缆密封好，接好接地线，紧固好螺钉，上述各项检查无误后，既可通电使用。 2、防爆灯不得随意拆卸，维护时，须断开前级电源后才可开盖检修或更换灯泡。 3、在维修过程中不得损坏隔爆面，维修后涂204-1防锈油，合好盖，紧固后方可使用。 4、防爆灯应定期检查，发现零件损坏应及时更换。 BAD83防爆无极灯 BEW防爆无极灯 ccd92防爆无极灯ccd93系列防爆无极灯 BAD81防爆无极灯

近年来，贵公司坚持以市场为导向，锐意进取，开拓创新，不断培育以技术创新为基础的竞争力，在激烈的市场竞争中迅速崛起，成为中国防爆行业的主导企业之一，建立了现代企业规章制度。
公司始终坚持“客户至上，质量”的宗旨，以不断创新和对客户满意的服务赢得市场。欢迎新老客户前来订购洽谈.

Mainly suitable for explosive gas atmospheres of Zone 1 or Zone 2 hazardous areas, Ⅱ C or the Ⅱ B class T2 group and the following places in AC 50Hz, rated voltage up to 220V circuit, used as a workplace lighting.

Two BAD83 explosion-proof induction lamp structure explosion-proof lamps aluminum alloy shell, glass and protection network consisting of several parts. The flameproof institutions. The shell is made of explosion-proof lights ZL102 cast aluminum alloy and glass tempered glass. The explosion-proof lights with internal and external ground screw and wiring cavity, suitable cable or steelpipe. The explosion-proof lights can have a variety of installation methods, the use of the rapid dismantling the structure, quick and easy lamp replacement. Integrated explosion-proof lamps, ballasts can be placed in the lamp body, good looks, split explosion-proof lamps, ballasts need to reprovision.

Explosion-proof, BAD83 explosion-proof induction lamp lights under the following conditions can be reliably work 1, does not restrict the altitude of the installation site. 2, the ambient temperature of -20 ° C to +40 ° C, and the mean value is not more than 35 ° C within 24h, the installation location of the air relative humidity not more than 50% at a maximum temperature of +40 ° C, at a lower the temperature allows a higher relative humidity, the wettest month average minimum temperature does not exceed +25 ° C, the maximum average monthly relative humidity does not exceed 90%. 4, severe vibration, shock and shake the place. 5 containing explosive gas atmospheres places. 6, the pollution level of the three.

, BAD83 explosion-proof induction lamp and maintenance of an explosion-proof lamps should check the nameplate on the basic parameters listed in the technical data and manual in line with the actual usage, and check the components for damage before installing, each part is intact. properly. First incoming cable installation by introducing a device connected to the terminals of the wiring chamber and compress the seal, the cable sealed, connect the ground wire to tighten the screws, the above examinations correct, both energized to use. 2, explosion-proof lights shall not disassemble, maintenance former level power should be disconnected before opening the lid to repair or replace the lamp. 3, in the maintenance process shall not damage the flameproof surface maintenance coating 204-1 after anti-rust oil, Hao cover, fastening before use. 4, explosion-proof lights should be checked regularly to find parts damage should be replaced. Promise lights, BAD83 explosion-proof BEW the explosion electrodeless lamp ccd92 explosion-proof Promise the lights ccd93 series explosion-proof Promise the lights BAD81 explosion-proof induction lamp

In recent years, the company adhere to market-oriented, forge ahead, pioneering and innovative, constantly cultivating core competitiveness based on technological innovation in the fierce market competition, rapid rise to become one of the leading enterprises of China's proof industry established The modern corporate rules and regulations.
The company always adhere to the "customer first, quality first" purpose, innovation and the customer satisfaction service to win the market. Welcome to the new and old customers come to order to negotiate

 世人都犯了罪 亏缺了神的荣耀 神爱世人 将他的独生子【耶稣】赐给我们 为我们的罪钉死在十字架上 搭建了世人去天堂的路   神说；他就是生命 就是光 。光照在黑暗里 黑暗却不接受光。 朋友 认识耶和华是智慧的开端 回来吧  愿神祝福您

BAD83防爆无极灯 ，BEW防爆无极灯 ccd92防爆无极灯，ccd93系列防爆无极灯 ，BAD81防爆无极灯 BAD83系列防爆无极灯是公司主打产品之一 价格和质量也是防爆行业的标准 是公司销量的产品  以此本公司向广大客户推荐此类产品 望广大客户前来咨询订购

一，主要适用于爆炸性气体环境中1区或2区危险区域，为ⅡC或ⅡB类T2组及以下场所，在交流50Hz、额定电压至220V的电路中，作为工作场所照明之用。

二，BAD83防爆无极灯主要结构防爆灯由铝合金外壳、玻璃罩和保护网等几部分组成。隔爆型机构。防爆灯的外壳采用ZL102铸铝合金压铸制成，玻璃罩采用钢化玻璃制成。防爆灯设有内外接地螺钉和接线腔，适合电缆或钢管布线。防爆灯可有多种安装方式，采用快速拆装结构，便于快速更换灯泡。一体式防爆灯，镇流器可放入灯体内，外型美观，分体式防爆灯，镇流器需另配。

三，BAD83防爆无极灯防爆灯在下列条件下能够可靠工作 1、安装地点的海拔不限制。 2、周围环境温度为-20℃～+40℃时，且24h内的平均值不超过35℃ 3、安装地点的空气相对湿度在温度为+40℃时，不超过50%，在较低的温度下允许有较高的相对湿度，湿的月平均温度不超过+25℃，该月平均相对湿度不超过90%。 4、在无剧烈振动，冲击及摇动的地方。 5、在含有爆炸性气体环境场所。 6、污染等级为3级。

四、BAD83防爆无极灯使用及维修 1、防爆灯在安装前，应检查铭牌上所列技术数据及使用说明书中的基本参数是否与实际使用情况相符，并检查元件是否损坏、各部位是否完好、正常。安装时先将进线电缆通过引入装置接到接线腔的接线端子上，并压紧密封圈，使电缆密封好，接好接地线，紧固好螺钉，上述各项检查无误后，既可通电使用。 2、防爆灯不得随意拆卸，维护时，须断开前级电源后才可开盖检修或更换灯泡。 3、在维修过程中不得损坏隔爆面，维修后涂204-1防锈油，合好盖，紧固后方可使用。 4、防爆灯应定期检查，发现零件损坏应及时更换。 BAD83防爆无极灯 BEW防爆无极灯 ccd92防爆无极灯ccd93系列防爆无极灯 BAD81防爆无极灯

近年来，贵公司坚持以市场为导向，锐意进取，开拓创新，不断培育以技术创新为基础的竞争力，在激烈的市场竞争中迅速崛起，成为中国防爆行业的主导企业之一，建立了现代企业规章制度。
公司始终坚持“客户至上，质量”的宗旨，以不断创新和对客户满意的服务赢得市场。欢迎新老客户前来订购洽谈.

Mainly suitable for explosive gas atmospheres of Zone 1 or Zone 2 hazardous areas, Ⅱ C or the Ⅱ B class T2 group and the following places in AC 50Hz, rated voltage up to 220V circuit, used as a workplace lighting.

Two BAD83 explosion-proof induction lamp structure explosion-proof lamps aluminum alloy shell, glass and protection network consisting of several parts. The flameproof institutions. The shell is made of explosion-proof lights ZL102 cast aluminum alloy and glass tempered glass. The explosion-proof lights with internal and external ground screw and wiring cavity, suitable cable or steelpipe. The explosion-proof lights can have a variety of installation methods, the use of the rapid dismantling the structure, quick and easy lamp replacement. Integrated explosion-proof lamps, ballasts can be placed in the lamp body, good looks, split explosion-proof lamps, ballasts need to reprovision.

Explosion-proof, BAD83 explosion-proof induction lamp lights under the following conditions can be reliably work 1, does not restrict the altitude of the installation site. 2, the ambient temperature of -20 ° C to +40 ° C, and the mean value is not more than 35 ° C within 24h, the installation location of the air relative humidity not more than 50% at a maximum temperature of +40 ° C, at a lower the temperature allows a higher relative humidity, the wettest month average minimum temperature does not exceed +25 ° C, the maximum average monthly relative humidity does not exceed 90%. 4, severe vibration, shock and shake the place. 5 containing explosive gas atmospheres places. 6, the pollution level of the three.

, BAD83 explosion-proof induction lamp and maintenance of an explosion-proof lamps should check the nameplate on the basic parameters listed in the technical data and manual in line with the actual usage, and check the components for damage before installing, each part is intact. properly. First incoming cable installation by introducing a device connected to the terminals of the wiring chamber and compress the seal, the cable sealed, connect the ground wire to tighten the screws, the above examinations correct, both energized to use. 2, explosion-proof lights shall not disassemble, maintenance former level power should be disconnected before opening the lid to repair or replace the lamp. 3, in the maintenance process shall not damage the flameproof surface maintenance coating 204-1 after anti-rust oil, Hao cover, fastening before use. 4, explosion-proof lights should be checked regularly to find parts damage should be replaced. Promise lights, BAD83 explosion-proof BEW the explosion electrodeless lamp ccd92 explosion-proof Promise the lights ccd93 series explosion-proof Promise the lights BAD81 explosion-proof induction lamp

In recent years, the company adhere to market-oriented, forge ahead, pioneering and innovative, constantly cultivating core competitiveness based on technological innovation in the fierce market competition, rapid rise to become one of the leading enterprises of China's proof industry established The modern corporate rules and regulations.
The company always adhere to the "customer first, quality first" purpose, innovation and the customer satisfaction service to win the market. Welcome to the new and old customers come to order to negotiate

 世人都犯了罪 亏缺了神的荣耀 神爱世人 将他的独生子【耶稣】赐给我们 为我们的罪钉死在十字架上 搭建了世人去天堂的路   神说；他就是生命 就是光 。光照在黑暗里 黑暗却不接受光。 朋友 认识耶和华是智慧的开端 回来吧  愿神祝福您

一，主要适用于爆炸性气体环境中1区或2区危险区域，为ⅡC或ⅡB类T2组及以下场所，在交流50Hz、额定电压至220V的电路中，作为工作场所照明之用。

二，BAD83防爆无极灯主要结构防爆灯由铝合金外壳、玻璃罩和保护网等几部分组成。隔爆型机构。防爆灯的外壳采用ZL102铸铝合金压铸制成，玻璃罩采用钢化玻璃制成。防爆灯设有内外接地螺钉和接线腔，适合电缆或钢管布线。防爆灯可有多种安装方式，采用快速拆装结构，便于快速更换灯泡。一体式防爆灯，镇流器可放入灯体内，外型美观，分体式防爆灯，镇流器需另配。

三，BAD83防爆无极灯防爆灯在下列条件下能够可靠工作 1、安装地点的海拔不限制。 2、周围环境温度为-20℃～+40℃时，且24h内的平均值不超过35℃ 3、安装地点的空气相对湿度在温度为+40℃时，不超过50%，在较低的温度下允许有较高的相对湿度，湿的月平均温度不超过+25℃，该月平均相对湿度不超过90%。 4、在无剧烈振动，冲击及摇动的地方。 5、在含有爆炸性气体环境场所。 6、污染等级为3级。

四、BAD83防爆无极灯使用及维修 1、防爆灯在安装前，应检查铭牌上所列技术数据及使用说明书中的基本参数是否与实际使用情况相符，并检查元件是否损坏、各部位是否完好、正常。安装时先将进线电缆通过引入装置接到接线腔的接线端子上，并压紧密封圈，使电缆密封好，接好接地线，紧固好螺钉，上述各项检查无误后，既可通电使用。 2、防爆灯不得随意拆卸，维护时，须断开前级电源后才可开盖检修或更换灯泡。 3、在维修过程中不得损坏隔爆面，维修后涂204-1防锈油，合好盖，紧固后方可使用。 4、防爆灯应定期检查，发现零件损坏应及时更换。 BAD83防爆无极灯 BEW防爆无极灯 ccd92防爆无极灯ccd93系列防爆无极灯 BAD81防爆无极灯

近年来，贵公司坚持以市场为导向，锐意进取，开拓创新，不断培育以技术创新为基础的竞争力，在激烈的市场竞争中迅速崛起，成为中国防爆行业的主导企业之一，建立了现代企业规章制度。
公司始终坚持“客户至上，质量”的宗旨，以不断创新和对客户满意的服务赢得市场。欢迎新老客户前来订购洽谈.

Mainly suitable for explosive gas atmospheres of Zone 1 or Zone 2 hazardous areas, Ⅱ C or the Ⅱ B class T2 group and the following places in AC 50Hz, rated voltage up to 220V circuit, used as a workplace lighting.

Two BAD83 explosion-proof induction lamp structure explosion-proof lamps aluminum alloy shell, glass and protection network consisting of several parts. The flameproof institutions. The shell is made of explosion-proof lights ZL102 cast aluminum alloy and glass tempered glass. The explosion-proof lights with internal and external ground screw and wiring cavity, suitable cable or steelpipe. The explosion-proof lights can have a variety of installation methods, the use of the rapid dismantling the structure, quick and easy lamp replacement. Integrated explosion-proof lamps, ballasts can be placed in the lamp body, good looks, split explosion-proof lamps, ballasts need to reprovision.

Explosion-proof, BAD83 explosion-proof induction lamp lights under the following conditions can be reliably work 1, does not restrict the altitude of the installation site. 2, the ambient temperature of -20 ° C to +40 ° C, and the mean value is not more than 35 ° C within 24h, the installation location of the air relative humidity not more than 50% at a maximum temperature of +40 ° C, at a lower the temperature allows a higher relative humidity, the wettest month average minimum temperature does not exceed +25 ° C, the maximum average monthly relative humidity does not exceed 90%. 4, severe vibration, shock and shake the place. 5 containing explosive gas atmospheres places. 6, the pollution level of the three.

, BAD83 explosion-proof induction lamp and maintenance of an explosion-proof lamps should check the nameplate on the basic parameters listed in the technical data and manual in line with the actual usage, and check the components for damage before installing, each part is intact. properly. First incoming cable installation by introducing a device connected to the terminals of the wiring chamber and compress the seal, the cable sealed, connect the ground wire to tighten the screws, the above examinations correct, both energized to use. 2, explosion-proof lights shall not disassemble, maintenance former level power should be disconnected before opening the lid to repair or replace the lamp. 3, in the maintenance process shall not damage the flameproof surface maintenance coating 204-1 after anti-rust oil, Hao cover, fastening before use. 4, explosion-proof lights should be checked regularly to find parts damage should be replaced. Promise lights, BAD83 explosion-proof BEW the explosion electrodeless lamp ccd92 explosion-proof Promise the lights ccd93 series explosion-proof Promise the lights BAD81 explosion-proof induction lamp

In recent years, the company adhere to market-oriented, forge ahead, pioneering and innovative, constantly cultivating core competitiveness based on technological innovation in the fierce market competition, rapid rise to become one of the leading enterprises of China's proof industry established The modern corporate rules and regulations.
The company always adhere to the "customer first, quality first" purpose, innovation and the customer satisfaction service to win the market. Welcome to the new and old customers come to order to negotiate

 世人都犯了罪 亏缺了神的荣耀 神爱世人 将他的独生子【耶稣】赐给我们 为我们的罪钉死在十字架上 搭建了世人去天堂的路   神说；他就是生命 就是光 。光照在黑暗里 黑暗却不接受光。 朋友 认识耶和华是智慧的开端 回来吧  愿神祝福您