500V电流保险丝座
价格:电议
地区:江苏 无锡市
电 话:86 0510 85319106
手 机:13771533196
传 真:86 0510 85319100
CLEARING TIME
熔 断 时 限
       
电流Ampere100%   Rating135%   Rating200%   Rating
时间Time4h<1h<120s
电压Volfage250v250v250v
       
5.机械特性Mechanical Properties:Terminal Conncctions&Lead Solderability 
乃经下述三项实验证明
5.1拉力强度Terminal Strength:当施加轴力向拉力1.1磅于两端导线(或套盖)5分钟后,
   无松动或损坏现象发生。     
5.1Leads and/or caps are soldcred(adhcred)to withstand axial pulling force1.1pounds5 
   min without loosening ou any harfulness to firmly arlachment  
5.2 回转强试Torsion Strength:    
   1 固定一端铜头,另一端施加720 g/cm的力左右摇动,铜头不得拉动及发生任何本体损坏
       
         After being subjecteedd to720 g/cmtorsion go one cap while te othe terminal fixed,no any
         damage or loosmning resulted    
       
2 一端导线弯折90度,本体以原轴旋转360度(五秒),三次不同方向旋转。导线或结合处不
       
     发生损坏     
       One lead bent through90o,the body be clamped and rotated through 360o at a rate or 5 sec
       about the original axis,Vophisical damage to leads or connections twsulted after 3 successive
       -altematero-tations.     
5.3 弯折强度Bending Strength:导线经过两次反方向之弯折后(弯折90度同折回原位谓之
   弯折)不发生损坏     
     After two bends of opposite ditections (bending through an angle of90oand back is detined as
     one bond)of lead,no damage are to be visualized.   

玻  管  式  保  险  丝        
Fuscs for Instrumcnt,Power and Telephone (Nonindicating)        
1.适应范围:本标准试用于保护仪器,各类电子电器元件,电源供应器和电话机用之玻管式熔断保险丝        
1.Available Ramge:For protccting instrurucnts,all electron or electonal,power supplics and telephone sets.        
2.形状及尺寸如下图,单位:mm        
2.Shape&size as following illustrations,unit:mm        
        
        
        
        
        
                           
         
        
        
2.1构造形状Structurc&Shape如上图 1as shown in ligure above          
  5mm X 20mm                     formall called        
2.2额定电压 Rated Voltage:                                            250V                                     AC.    250V    
2.2额定电流 Ratde Current:                       150MA-15A 慢熔   
        
NO Parr Name 部 名  Material   材料   Size  尺寸  
A Ferrule Cap 套合(铜帽)  Capper(inckel plaring)铜(镀镍)   5.16*5.25  
B Tube 铜管  "Soda Glass (transparenl)
石灰玻璃(透明)"   4.7x19.1mm  
C "Fuse Soluble Eloment
可熔体"  Siler Alloy 银合金线     
D Adhesive 粘胶  "Resin &Hardening Agent
树脂与硬剂"     
E Solder 焊锡  "Naught Lead Tin
无铅锡"     
F Pig 引线  Capper Plaring Tin 铜镀锡   0.65x38x5.85  
        
        
        
3.材   料:        
3.Material        
3.1 玻管本体:透明玻璃管可清晰见到内部之熔线但不可破裂或变形        
3.1 Glass tube:Transparenr glass in which the fuse is clesr and pwspcctable.No breaking or deformation        
    is allowed.        
3.2 两端铜帽:须以导电率良好之黄铜底材料。        
3.2 Two brass end caps Made of brass of good conductiviry.        
3.3 铜帽处理:铜帽部分镀镍        
              标示后若加"3"者,表示须镀镍。        
3.3 Coating of brass caps Plaring the surfacc with nickel If the indicarion is added with"s",it needs        
    to be plard with silver.        
3.4 铜盖强度:铜盖和玻璃本体间的扭力小720g-cm.        
3.4 Slrcmgth of brass caps The minimum tortion between brass caps and glass tube is 720g-cm        
4.电气特性:        
4.Charactcristics of Electrical Appliancos        
4.1 负载容量:额定电流测100%,能继续通电无任何熔化现象。        
4.1 Loading Capacity The Listed Electrical.(Included) add 100%for following,and it's available to let        
    Current Kurrcnt Keep on flowinng without any melding        
4.2 温度特性:进行上项测试1.5  小时,后继续维持原加之电流,每隔十分钟测试,继续测试        
    三次,温度不得升高,若使用热偶式测量方法,(Thermometer method)则本体温度在70℃以下        
    若使用温度计测量方法(Thermometer method)则在50℃以下。        
4.2 Temperature proceed: the prccedingtest for1.5  hours,keep testing iteith the original current        
    every 10 minutes.Continue to test it for 3 times .The temperature is not allowed to be higher