摩擦型扭力限制器
价格：电议
地区：
电 话：86 0519 86357553
手 机：13815003185
传 真：86 0519 89825606
-
图文详情
-
产品属性
-
相关推荐
摩擦型扭力限制器Friction Type Torque Limiter
尺寸/Dimension
规格 No. | 扭力范围 TorqueRange Kgf.m | 标准 孔径 Stock Bore mm | 孔径 Max. Bore mm | 轴衬 长度 Bushing length | 轴衬外径 Bushing Outside diameter | 中心构件 孔径 Central Member Bore | D | DH | L | B | T | t | S | A | C | 调整 螺母 Adjust Nut | 调整 螺栓 Adjust Bolt | 固定 螺丝 Fixing Screw | 重量 Weight （kgf） |
SS200-1 | 0.3~1 | 8 | 14 | 3.6 | 30-0.024 -0.049 | 30+0.3 0 | 50 | 24 | 29 | 6.5 | 2.6 | 2.5 | 7 | - | 38 | M24 P1.0 | - | - | 0.2 |
SS200-2 | 0.7~2 | ||||||||||||||||||
SS250-1 | 0.7~2.8 | 10 | 22 | 4.5 | 41-0.010 -0.045 | 41+0.05 0 | 65 | 35 | 48 | 16 | 4.5 | 3.2 | 9 | 4 | 50 | M35 P1.5 | - | M5 | 0.5 |
SS250-2 | 1.4~5.5 | ||||||||||||||||||
SS350-1 | 2.0~7.6 | 17 | 25 | 6.5 | 49-0.025 -0.065 | 49+0.05 0 | 89 | 42 | 62 | 19 | 4.5 | 3.2 | 16 | 6 | 63 | M42 P1.5 | - | M6 | 1.2 |
SS350-2 | 3.5~15.2 | ||||||||||||||||||
SS500-1 | 4.8~21.4 | 20 | 42 | 6.5 | 74-0.05 -0.010 | 74+0.05 0 | 127 | 65 | 76 | 22 | 5.7 | 3.2 | 16 | 7 | - | M65 P1.5 | M8 3psc | M8 | 3 |
SS500-2 | 9.0~42.9 | ||||||||||||||||||
SS700-1 | 11.8~58.1 | 30 | 64 | 9.5 | 105-0.075 -0.125 | 105+0.05 0 | 178 | 95 | 98 | 24 | 7.7 | 3.2 | 29 | 8 | - | M95 P1.5 | M10 3psc | M10 | 6.7 |
SS700-2 | 22.8~110.6 |
摩擦型扭力限制联轴器Friction Type Torque Limiter
尺寸表/Specification
规格 No. | 扭力范围 Torque Range Kgf.m | 转数 Max. Rotational Frequency rpm | 普通内径/Stock Bore | 内径 Max. Inside Diameter | 链轮 Sprocket | D | DH | L | L1 | L2 | s | 重量 Weight (kgf) | ||
联轴器侧 Coupling Side | 扭力限 制器侧 Limiter Side | 联轴器侧 Coupling Side | 扭力限 制器侧 Limiter Side | |||||||||||
SS200-1C | 0.3~1 | 1200 | 8 | 8 | 31 | 14 | RS 40-16T | 76 | 50 | 55 | 24 | 29 | 7.5 | 1.0 |
SS200-2C | 0.7~2 | |||||||||||||
SS250-1C | 0.7~2.8 | 1000 | 13 | 10 | 38 | 22 | RS 40-22T | 102 | 56 | 76 | 25 | 48 | 7.4 | 2.0 |
SS250-2C | 1.4~5.5 | |||||||||||||
SS350-1C | 2.0~7.6 | 800 | 13 | 17 | 45 | 25 | RS 50-24T | 137 | 72 | 103 | 37 | 62 | 9.7 | 5.2 |
SS350-2C | 3.5~15.2 | |||||||||||||
SS500-1C SS500-2C | 4.8~21.4 9.0~42.9 | 500 | 18 | 20 | 65 | 42 | RS 60-28T | 188 | 105 | 120 | 40 | 76 | 11.6 | 12.3 |
SS700-1C | 11.8~58.1 | 400 | 23 | 30 | 90 | 64 | RS 80-28T | 251 | 150 | 168 | 66 | 98 | 15.3 | 31.0 |
SS700-2C | 22.8~110.6 |
链轮之配合参考表/ Applicable Sprockets
规格 No. | 中心构件 孔径 Central Member Bore | 少链轮节距和齿数/Min. Sprocket Pitch and Number of Teeth | |||||||||||||
3/8” -#35 | 1/2” -#40 | 5/8” -#50 | 3/4 -#60 | 1” -#80 | 11/4” -#100 | 11/2” -#120 | |||||||||
少链 轮齿数 Min Sprocket Teeth | 轴衬长度 Bushing length (mm) | 少链 轮齿数 Min Sprocket Teeth | 轴衬长度 Bushing length (mm) | 少链 轮齿数 Min Sprocket Teeth | 轴衬长度 Bushing length (mm) | 少链 轮齿数 Min Sprocket Teeth | 轴衬长度 Bushing length (mm) | 少链 轮齿数 Min Sprocket Teeth | 轴衬长度 Bushing length (mm) | 少链 轮齿数 Min Sprocket Teeth | 轴衬长度 Bushing length (mm) | 少链 轮齿数 Min Sprocket Teeth | 轴衬长度 Bushing length (mm) | ||
SS200 | 30+0.03 0 | 20 | 38 | 16 | 6 |
|
|
|
|
|
|
|
|
|
|
SS250 | 41+0.05 0 |
|
| 20 | 4.5 | 17 | 6.5 |
|
|
|
|
|
|
|
|
SS350 | 49+0.05 0 |
|
| 26 | 4.5 | 21 | 6.5 | 18 | 9.5 | 15 | 9.5 |
|
|
|
|
SS500 | 74+0.05 0 |
|
| 35 | 4.5 | 29 | 6.5 | 25 | 9.5 | 19 | 9.5 |
|
|
|
|
SS700 | 105+0.05 0 |
|
| 48 | 4.5 | 39 | 6.5 | 33 | 9.5 | 26 | 9.5 | 21 | 12.5 | 18 | 12.5 |
注意事项/Note:
- 1. 中心构件之摩擦面必须研磨加工以得额定之扭力，并成为平坦、平行，与内径相垂直，不含任何灰尘，锈皮或油污为宜。
The friction surface of central member must be polished to gain the rated torque to provide flatness, parallel and perpendicularity to inside diameter, and to retain freed from dust, burr or oil.
- 2. 内环之选择不可大于中心构件的宽度，中心构件厚度见表中之S尺寸。
The inner ring is no greater than the width of central member. Please refer to the S dimension in the table to seek for the max. thickness of central part.
摩擦式扭力限制器
Friction Type of Torque Limiter
扭力值与锁紧螺帽调整关系图
Torque Value to Nut Packing Adjustment