IEC60950-1&GB4943.1信息技术类设备检测实验室配置清单

技术资料

仪器仪表首页

发布时间：2018/1/9 9:17:00

IEC60950-1&GB4943.1信息技术类设备检测实验室仪器设备推荐清单：

SAR 测试

手机性能测试

EMC暗室测试

序号	条款号	检测内容	所需检测仪器设备	要求和量程要求	所需检测仪器、设备
序号	条款号	检测内容	所需检测仪器设备	要求和量程要求	设备名称	设备型号	设备量程	设备
3	1.6.2	Input Current	Amp-meter		数字功率计	WT310	0—500V 0—20A 0—10kW	±1.5%
4	2.1.1.1	Access to energized parts	Test finger (joint /rigid 30N, fig. 2A)	See fig. 2A	关节试验指	GS-IP100	fig. 2A	fig. 2A
5	直型试验指	GS-IP11	fig. 2A	fig. 2A
6		推拉力计	ANF-50	0—50N	±1N
7	Test pin (fig. 2B 4mm/3mm/15 mm long)	See fig. 2B	试验销	GS-IP03	fig. 2B	fig. 2B
8	Test probe (fig. 2C 12mm/80mm)	See fig. 2C	试验探头	GS-IP05	fig. 2C	fig. 2C
9	2.1.1.5	Energy Hazard	Variable resistive load		电子负载	3250	AC/DC 0-60V 0-20A 0-300W	±1.5%
10	2.1.1.7	Plug discharge	Measuring instrument with input impedance 100MΩ ±5 MΩ in parallel with an input capacitance of 25pF or less.		示波器	F196C	2mV-100V/div 5ns-5s/div 100M	±0.2%
11		高压探棒	N2771A	0-10kV	±1%
12	2.1.1.9	Audio Amplifiers	Suitable signal generator and audio power measuring equipment		噪声信号发生器	DF1681	20-20kHz 0-70dB	±1dB
13		音频信号发生器	GAG-810	10-1000kHz	±1.5%
14	2.3.1	Limits of TNV circuits	Resistor 5000Ω ± 2%,	±2%	试样电阻	5kΩ	5000Ω	±0.3%
15	2.3.4	Connection of TNV circuits to other circuits	Resistor 5000Ω ± 2%,	±2%	试样电阻	5kΩ	5000Ω	±0.3%
16	2.3.5	Test for operating voltages generated externally	Test generator	120V± 2V a.c., 50 or 60 Hz, 1200Ω ± 2%	试验电压发生器	GS-TNV10	0-240V 50 or 60 Hz 1200Ω	±1%
17	2.4.2	Limited current circuits, limit values	Resistor 2 000 Ω ± 10%,	± 10%	试样电阻	2kΩ	2000Ω	±0.5%
18	Capacitance measuring device		LCR测量仪	4263B	10μH-1H 1pF-1μF 0.1Ω-100kΩ	±0.1%
19	2.6.3.4	Resistance of earthing conductors	High current source with a voltage not exceeding 12 V		接地电阻测试仪	TOS6210	0—0.2Ω	±0.002Ω
20	2.9.2	Humidity conditioning	Chamber (91% Rh...95% Rh, 20...30 ° C)		调温（调湿）箱	GS-TH800	-40—150℃ 0-95%RH	±2℃，±2.5%RH
21	2.10	Creepage distance/clearance/distance through insulation (determination of requirements; working voltage measurements)	Oscilloscope		示波器	F196C	2mV-100V/div 5ns-5s/div 100M	±0.2%
22	Creepagedistance/clearance/distance through insulation (measurements)	Dial gauge		爬电距离测试卡	CC-23	1.0—8.0mm	0.1mm
23	Micrometer		游标卡尺	150mm	0—150mm	0.02mm
24	Microscope		读数显微镜	Vibao	0-100mm	±0.05mm
25	2.10.3.9	Measurement of transient levels	Test-generator; reference 2 of table N.1		脉冲发生器	1950S	脉冲波形：1.2×50μs电压：0-7KV	±5%
26		脉冲发生器	1950S	脉冲波形：10×700μs电压：0-7KV	±5%
27	2.10.4	Creepage distances	Test equipment for tracking		漏电起痕试验装置	GS-TK20	0-600V 0-1A	±1%
29	2.10.9 & 2.10.10 & 2.10.11 (and 2.10.8.2)	Thermal cycling and thermal ageing	Full draught oven (± 2oC) Cooling facility (0o C)	± 2oC	调温（调湿）箱	GS-TH800	-40—150℃ 0-95%RH	±2℃，±2.5%RH
30	2.10.8.4	Abrasion resistance test	Scratch test device with steel pin	20mm/s; 10±0.5N, 80~85°	耐划痕试验仪	GS-NH300	20mm/s;10±0.5N, 80~85°	±2%
31	顶角40度，倒圆半径0.25mm±0.02mm	钢针	\	顶角40度，倒圆半径0.25mm±0.02mm	±1degree，±0.02mm
32	2.10.7	Enclosed and sealed parts	See 2.10.9 & 2.10.10	± 2oC	调温（调湿）箱SETH-Z-061LK	GS-TH800	-40—150℃ 0-95%RH	±2℃，±2.5%RH
33	3.1.5, 3.1.9 and 4.2.2	10 N steady force test	Suitable tool for applying steady force of 10 N +/- 1N	±1N	推拉力计	ANF-50	0—50N	±1N
35	3.2.6	Cord anchorage and strain relief	Appropriate weights		电源线拉扭试验机	GS-DXLN20	0-50kg	±1%
36	3.2.8	Cord guards	Appropriate weights		推拉力计	ANF-50	0—50N	±1N
37	4.1	Stability	Inclined plane 10°		倾斜平台	GS-QX800	0-15o	±3%
38	Force 250N		推拉力计	ZP-1000	0-1000N	±0.2%
39	Test tool 800N with a flat surface 12,5cm by 20cm		推拉力计	ZP-1000	0-1000N	±0.2%
40	金属平面	136	12,5cm by 20cm	±0.5%
41	4.2.3	Steady force test 30 N	Test finger (rigid 30N± 3N, fig. 2A)		直型试验指	GS-IP11	fig. 2A	fig. 2A
42	推拉力计	ANF-50	0—50N	±1N
43	4.2.4	Steady state force, 250 N	Test tool 250N± 10N with a circular plan surface ? 30mm.		推拉力计	ZP-1000	0-1000N	±0.2%
44	金属平面	GS16	? 30mm	±0.1mm
45	4.2.5	Impact test	? 50mm/500g± 25g steel ball	500g± 25g	冲击钢球	GS-IP07	500g ? 50mm	+10g，+0.004mm
46	4.2.6	Drop test	Hard wood 13mm on 19mm to 20mm plywood, two layers		跌落平台	GS207	/	/
47	4.2.7	Stress relief	Oven 70K over normal temp		高温试验箱	GS-GW005	室温—200℃	±1℃
49	4.2.10	Wall or ceiling mounted equipment	Several weights		推拉力计	ZP-1000	0-1000N	±0.2%
50	4.3.2	Handles and manual controls	Force 15N/20N/30N/50N		推拉力计	ANF-50	0—50N	±1N
51	4.3.6	Direct plug-in equipment	Test equipment (see Fig. 11 of IEC 60065)		插头力矩测试仪	GS-CTN04	0-0.25Nm	±1%
53	4.3.13.2	Ionizing radiation	Ionization meter (Annex H)		电离辐射计	440RF/D	0-1000μSV/h	±20%
57	4.4	Protection against hazardous moving parts	Test finger (joint /rigid 30N, fig. 2A)	See fig. 2A	关节试验指	GS-IP100	fig. 2A	fig. 2A
58	直型试验指	GS-IP11	fig. 2A	fig. 2A
59		推拉力计	ANF-50	0—50N	±1N
60	4.5	Thermal requirements
61	Voltage supply	Single phase voltage supply systems/variability/adequacy		变频电源	6902	0-300V 0-15A	±1.5%
62	Three phase voltage supply systems		变频电源	AFR-360	60kVa	±1.5%
63	Temperature (rise)	Temperature recorder (multi-channel)		记录仪	DR232-02-00-1R	0—300℃	±0.5℃
64	Thermocouples		热电偶	TT-K-30	0—150℃	±0.5℃
65	Winding resistance (normally > 1,0 Ω 2-wire, 4-wire<1,0 Ω ).		数字多用表	34401A	0.1-100MΩ	±3%
66	Voltage	Voltmeters (ac/dc)		数字多用表	34401A	0—1000V	±1%
67	High voltage meter (probe)		高压探棒	N2771A	0-10kV	±1%
68	Current	Currents (ac/dc)		数字功率计	WT310	0—500V 0—20A 0—10kW	±1.5%
69	Loading	Loads (resistive)		电子负载	3250	AC/DC 0-60V 0-20A 0-300W	±1.5%
70	4.5.5	Resistance to abnormal heat	Ball pressure test apparatus according to IEC 60695-10-2 Oven at least 125oC	球直径：5mm；砝码：20N±0.2N	球压试验装置	GS-QY21	球直径：5mm；砝码：20N	±0.2N
71		高温试验箱	GS-GW005	室温—200℃	±1℃
72	4.6.2	Bottoms of fire enclosure	Distillate fuel oil as described in Annex A.3.2	10ml 1ml/s	灼热燃油	GS-ZRY06	10ml 1ml/s	±0.2ml ±0.1ml/s
73	4.6.4.2	Evaluation of larger openings	Suitable tool (or tools) to simulate a straight metal object, 1mm in diameter, length up to 13 mm	? 1mm	试验探针	GS-IP14	? 1mm	+0.044mm
74	4.6.5	Adhesives for constructional purposes	Oven up to 100 ° C		高温试验箱	GS-GW005	室温—200℃	±1℃
75	4.7.3	Materials, Tests see Annex A	V-1, V-2, HF-2, 5V	IEC60695	针焰试验仪	GS-NF30	IEC60695	IEC60695
76	Bunsen burner (9,5 ± 0,5 mm)	IEC60695	UL94水平垂直燃烧试验仪	GS-HVUL20	IEC60695	IEC60695
77	Gas for burner (~37 MJ/m3)		甲烷气体	98%纯度以上	/	/
78	Oven for preconditioning		高温试验箱	GS-GW005	室温—200℃	±1℃
79	4.7.3.6	Materials used in high-voltage components	Test of Annex A or test of 14.4 of IEC 60065 or needle flame test according to IEC 60695-2-2	IEC60695	针焰试验仪/水平垂直燃烧仪	GS-NF30\GS-HVUL20	IEC60695	IEC60695
80	5.1	Touch current and protective conductor current	Measuring instruments of Annex D		泄漏电流测试仪	Simpson228	0-10mA	±1%
81	5.2	Electric strength	Test equipment with the relevant voltage and tripping current	短路电流>200mA	AC/DC耐压绝缘测试仪	TOS9201	AC:0-5kV， 0—110mA; DC:0-6kV, 0-10mA; 短路电流>200mA	±1%
83	6.2.1	Protection of equipment users from overvoltages on telecommunication networks	Test probe (Fig. 2C, 12mm/80mm)	See fig. 2C	试验探头	GS-IP05	fig. 2C	fig. 2C
84	6.2.2.1	Impulse Test	Impulse test generator according to Annex N		脉冲发生器	1950S	脉冲波形：10×700μs电压：0-7KV	±5%
85	6.2.2.3	Protection of equipment users from overvoltages on telecommunication networks	insulation resistance		绝缘电阻测试仪	TOS7200	0-1000V 0-2000MΩ	±0.5%
86	7.4.2	Voltage surge test	Test generator reference 3 of table N.1		浪涌测试仪	SUG10/700G	0-10kV	±5%
87	7.4.3	Impulse test	Test generator reference 1 of table N.1		脉冲发生器	1950S	脉冲波形：10×700μs电压：0-7KV	±5%